If you have a gas stove and it isn’t turning on, there are a few different things you can do to try to fix the problem. These include cleaning the pilot hole where the gas comes out, calling an electrician, and replacing the spark electrode.
Possible Causes For Stove Not Turning On
There are several possible causes for a stove not turning on. Here are some common ones:
- Electrical issues: If the stove is not receiving power, it will not turn on. This could be due to a tripped circuit breaker or a blown fuse. Check the circuit breaker or fuse box to see if there are any issues.
- Gas supply problems: If the stove is not receiving a sufficient supply of gas, it will not turn on. Check to make sure the gas valve is open and that the gas line is not blocked.
- Ignition issues: If the stove has an electronic ignition system, the ignition may not be working properly. This could be due to a faulty ignition switch or a problem with the ignition control module.
- Thermostat problems: If the stove has an electronic thermostat, it may not be working properly. This could cause the stove to not turn on or to shut off unexpectedly.
- Control panel issues: If the stove has a control panel, it may not be functioning properly. This could be due to a faulty control panel or a problem with the wiring.
If you are having trouble with your stove and are unsure of the cause, it is best to contact a qualified appliance repair technician for assistance.
Check if the igniter needs replacing
When fixing a stove that won’t turn on, one of the first things to check is the igniter. You may need to replace this part if it is faulty.
The igniter is located near the burners of your gas stove. It is a ceramic and metal component that produces a spark to light the flame. If the igniter is damaged, it can cause a weak or missing spark, causing your gas to fail to burn.
This component is relatively easy to access and is the first step to diagnosing a problem. Fortunately, you can easily replace it.
Before you start replacing the igniter, make sure you shut off the gas to the stove. That way, you won’t accidentally drop it and render it useless.
To clean the igniter, use a Q-tip dipped in rubbing alcohol. This will remove any debris, dirt or gunk that might be blocking the orifices.
Using a multi-meter is also a good way to test your ignition switch. You might need to unplug the oven to properly check it out.
One last thing to check is the temperature control thermostat. This is an electronic device that cycles on heat and off heat at low temperatures. Normally, it will be positioned inside the stovetop. A replacement can be purchased from the manufacturer.
After you’ve checked all the major components, you can turn the gas back on. As long as the burners aren’t burning, you can turn the oven on and test it out.
If you do need to replace the igniter, you can find replacement parts at CookerSpareParts.com. These professionals will help ensure that you are getting the correct part and that your local safety regulations are up to date.
Check the relays from the surface element board to the burner
The relays from the surface element board to the burner can be broken, causing the burners to not work. You should check them to see if they are working properly. If they are not, you should replace them.
The circuit design should include failsafe measures against disconnection. This can be achieved by including a diode in the DC circuit.
Incorrect application can also lead to the wrong voltage being applied to the coil. It can also result in the wires leading to the igniter burning out.
Dust and condensation can accumulate inside the Relay. This can cause insulation failure and contact failure. When the temperature changes suddenly, the insulation can deteriorate.
Contacts can also burn out over time. This can be triggered by the use of high rated devices. OMRON Relays are designed for particular sockets and atmospheres.
The switching capacity of the Relay varies greatly depending on the load. The load is based on the required service life. Larger relays handle higher currents and voltages. Smaller relays are better suited to low mechanical loads.
The Relay should not be used in environments with flammable gas, organic gases, and sulfidizing gases. They should also not be exposed to strong magnetic fields.
Relays should also not be exposed to water. If the Relay is sealed, then dust should be removed before mounting.
High humidity can cause oxidation on the contact surfaces. This can also lead to the formation of silicone oxide.
These are some of the common problems with the relays from the surface element board to the Burner. It is important to check the switches and contacts on the relays to determine if they are working.
Clean the pilot hole where the gas comes out
If you have a gas stove, you may be familiar with the pilot. It’s a small tube that leads from the gas valve to the burner. You can use a pipe cleaner or a soft-bristled brush to clean the orifice.
However, you need to be careful. Clogged or dirty pilots are a big fire hazard and can cause your gas appliance to malfunction. So, before you start a major cleaning project, check the gas supply. This can save you money.
Another thing you can do is check your thermocouple. The thermocouple measures the temperature of the gas and controls the pilot’s flame. An unhealthy or clogged pilot will not burn hot enough to reach the proper temperature.
The small pilot air inlet hole is located about two inches from the pilot’s flame. When cleaned, this should give you a centered, bright blue flame.
In order to do this, you will need a few tools. First, you will need to remove the unit from the furnace. Make sure that you don’t permanently bend the metal strip.
Once the unit has been removed, you should have access to the pilot’s orifice. It’s easy to remove this component from the pilot assembly. To do so, you’ll need to twist it to the left and unscrew it from its fitting.
Next, you’ll need to disassemble the ODS (or Pilot Assembly). Disassembling the ODS will allow you to get to the tiny air intake holes. A wire brush can help you to clean the tip.
Finally, you’ll need to turn off the gas. For this step, you’ll need to shut off the stove and all other appliances that are connected to the pilot. After doing this, you’ll need to wait about five minutes for the gas to exit the pilot.
Replace a spark electrode
If your gas stove or range is not turning on, you may need to replace a spark electrode. This is the final part of the chain that produces a spark that ignites the burner.
A spark electrode is a metal tip that produces a small spark that ignites the gas. It sits on the top of a burner on a freestanding gas range. You can also find them on the surface burners of a dual fuel range.
The top burner spark electrode can malfunction due to a number of reasons. One of the most common problems is accidental damage. Another cause is accumulated food particles. These particles can get in the way of the gas flow.
If your stove is not turning on and you hear a clicking sound, the first thing to check is the ignition switch. A defective spark module or wire can cause continuous or intermittent sparking.
Depending on your range, you may need to lift the cooktop to access the switch. If you need to do this, you will need to unplug the breaker from the wall. Turn the power off before lifting the burners.
Next, clean the burner parts to remove dirt, grease, and food particles. This will help to produce a strong spark. After cleaning the parts, a metallic pin can be used to remove debris. Dry the parts with a dry towel.
A spark electrode is also susceptible to wear and tear. You should replace it if it has been damaged or worn.
Some electrodes have ceramic insulation below their tip. If this is the case, a strong spark will not light the burner. Also, if the electrode is wet, it will make a clicking noise.
Call an electrician
If you’re having trouble getting a stove to light up, there are some things you can try first before calling an electrician. The most common problem is no gas getting to the burner. However, there are other causes for this.
First, make sure that your gas supply valve is turned on. You can do this by simply inserting a straightened paperclip into the orifice.
If no gas is getting to the burner, the problem may be with the igniter. This part can wear out and break over time. In this case, you may need to replace the module.
Another issue is an overloaded circuit. Overloaded circuits can occur when you use an air conditioner, an electric heater, or other electrical appliances. Reducing the amount of appliances that are on the same circuit can help.
If you see sparks when plugging in an electrical appliance, it could be an indicator of a problem with the power box or wiring. Getting a repair can be as simple as replacing a fuse or rewiring the system.
Depending on your home’s age, the fuse or circuit breaker may be outdated. It is important to contact a licensed electrician to inspect your wiring and make sure your appliances are working properly.
An older house may have aluminum wiring, which can corrode over time. This can lead to a short circuit or a fuse tripping. Your local electrician can check for corrosion in the service panel and any unsafe practices from the previous owner.
Using a multimeter to test the wires for resistance is a good way to detect a short circuit. However, some issues are more serious and require professional attention.
We service many popular Cities including the following within Brooklyn Borough or Kings County Service Area:
Brooklyn, Williamsburg, Northwest Brooklyn, New Lots, Borough Park, East New York, Bushwick, Flatbush, Central Brooklyn, Canarsie, Sunset Park, Greenpoint, Southern Brooklyn, Flatlands, Southwest Brooklyn